Home
› Diy Water Methanol Injection - Texas_Ace's Cheap DIY Meth/Water Injection kit Writeup! Get 10hp+ for under $150! - Page 12 ... / Intercooler is to cool down the hot, compressed air from the turbo.
Diy Water Methanol Injection - Texas_Ace's Cheap DIY Meth/Water Injection kit Writeup! Get 10hp+ for under $150! - Page 12 ... / Intercooler is to cool down the hot, compressed air from the turbo.
Diy Water Methanol Injection - Texas_Ace's Cheap DIY Meth/Water Injection kit Writeup! Get 10hp+ for under $150! - Page 12 ... / Intercooler is to cool down the hot, compressed air from the turbo.. Choose the one that best suits your needs. About press copyright contact us creators advertise developers terms privacy policy & safety how youtube works test new features press copyright contact us creators. Joined aug 24, 2008 · 387 posts. I have been wanting to do this for sometime but i have been too lazy. Only when methanol or alcohol was mixed with the water did i see an improvement.
This is a re.boot of the original video. Choose the one that best suits your needs. Meth injection is a reasonably simple concept. This page was the most popular entry page at our old web site. Since we don't need nearly as much water as a forced induction vehicle, the pump will pulse on and off because it has reached the 100psi limit.
Water Methanol Injection - More Boost! - YouTube from i.ytimg.com When air is cooled, it becomes very dense. Diy water methanol injection system using parallax propeller microcontroller. The term liquid intercooling with water/methanol injection refers to a highly atomized mist of water/methanol that is injected into the airstream and begins to evaporate. Water injection will also help vehicles that are driven in hot climates or when they are used for towing. Automobile engines produce unrelenting amounts of useless heat. Discussion starter · #1 · nov 3, 2012. Think of water methanol injection as a big time octane enhancer and added air charge cooling when dealing with forced inductions applications. This version is re.edited and has voice over information to accompany the subttitles as well as new music taken from.
My primary objective was to see if improvement in gas mileage was possible.
This version is re.edited and has voice over information to accompany the subttitles as well as new music taken from. Water injection will also help vehicles that are driven in hot climates or when they are used for towing. *if you just want a simple 1 stage kit this setup would cost about $280. There is no rule of thumb on how much timing or boost can be increased when running water methanol injection system. And you'll spend that small amount of money (heck, it takes. Welcome to the original diy alky page. Diy water methanol injection system using parallax propeller microcontroller. Ultimately the best mixture is 50/50 but ratios down to 30 percent methanol and 70 percent water can work well. If i can't tame the afrs via the o2 map (reconcile the fueling in a way that the ecu doesn't get wise), the ecu would trim out any additional fuel (methanol) along with the gasoline. Just create a 50/50 mixture of methanol and water. By adding four 12oz bottles of heet, to the one gallon of windshield washer fluid will give you a 50/50 mix of water and methanol. When air is cooled, it becomes very dense. Check out top brands on ebay.
This is a re.boot of the original video. From our tank tap adapter with incorporated filter, to our streamlined nozzle holder, each part in our system has been engineered to perform in the most strenuous conditions while maximizing. 100% water has the greatest cooling capacity, but because i was planning to use the windshield washer reservoir to supply the system i still wanted to be able to clean off my windshield and keep the fluid from freezing in cold weather. Choose the one that best suits your needs. I hope you find information here to help you achieve the level of performance you're looking for with your forced induction vehicle.
Water Injection 2008 - Page 7 - HomemadeTurbo - DIY Turbo Forum from www.homemadeturbo.com I hope you find information here to help you achieve the level of performance you're looking for with your forced induction vehicle. Each engine will react to it differently. A percentage of the total mixture consisting of some methyl alcohol (methanol) can also be used. By adding four 12oz bottles of heet, to the one gallon of windshield washer fluid will give you a 50/50 mix of water and methanol. While on pump gas and with a 50/50 mix of water methanol. In general most engines you can usually run the equivalent boost and timing of your 100 octane tune. *if you just want a simple 1 stage kit this setup would cost about $280. And you'll spend that small amount of money (heck, it takes.
This is completely over kill for our situation.
This is completely over kill for our situation. Only when methanol or alcohol was mixed with the water did i see an improvement. Here is my diy 2 stage water/methanol kit i put together for around $382.00. From our tank tap adapter with incorporated filter, to our streamlined nozzle holder, each part in our system has been engineered to perform in the most strenuous conditions while maximizing. *if you just want a simple 1 stage kit this setup would cost about $280. I am leaning toward water only injection and here's why. Discussion starter · #1 · nov 3, 2012. Discharge of the injected water is very small, in the form of water droplets. Meth injection is a reasonably simple concept. Check out top brands on ebay. In this video we show you how to install a water methanol system. We recommend that people purchase straight methanol and mix their own injection fluid to get the best in performance and reliability, explained mollica.the mix is easy; Homemade water injection for auto engines.
This version is re.edited and has voice over information to accompany the subttitles as well as new music taken from. If i can't tame the afrs via the o2 map (reconcile the fueling in a way that the ecu doesn't get wise), the ecu would trim out any additional fuel (methanol) along with the gasoline. Here is my diy 2 stage water/methanol kit i put together for around $382.00. Welcome to the original diy alky page. Homemade water injection for auto engines.
DIY water methanol injection system - YouTube from i.ytimg.com In the early days of dawes devices, we experimented extensively with creating a water injection kit that could be built for fraction of the cost of a purchased system, but would work just as well. Welcome to the original diy alky page. Basic mixing instructions are as follows. This is completely over kill for our situation. An easy yet mechanically invasive way to remove much of the engines heat is through water/methanol injection. Water has a very high specific heat rating (it can absorb. When air is cooled, it becomes very dense. Choose the one that best suits your needs.
We recommend that people purchase straight methanol and mix their own injection fluid to get the best in performance and reliability, explained mollica.the mix is easy;
Check out top brands on ebay. When air is cooled, it becomes very dense. In the early days of dawes devices, we experimented extensively with creating a water injection kit that could be built for fraction of the cost of a purchased system, but would work just as well. 1 of 2 go to page. This was our longest diy install we've done but in the end the difference it makes. Just create a 50/50 mixture of methanol and water. Choose the one that best suits your needs. Water injection, or water/alcohol injection, acts as a highly effective gaseous intercooler. Ultimately the best mixture is 50/50 but ratios down to 30 percent methanol and 70 percent water can work well. Water can do this job far better because it has a very An easy yet mechanically invasive way to remove much of the engines heat is through water/methanol injection. Only when methanol or alcohol was mixed with the water did i see an improvement. Diy water methanol injection system using parallax propeller microcontroller.
